Search
Search for "click":
(Click here to search this entire website for "click" with Google.)
 |
|
|
Clicker 2 for PIC32MZ is a compact PIC32 development kit with two mikroBUS™ sockets for click board connectivity. It carries the PIC32MZ 32-bit microcontroller (1 MB Live-Update Flash and 512 KB SRAM) microcontroller with FPU from Microchip. With a built-in USB-HID bootloader the Clicker 2 for PIC32MZ it easy to program. |
|
|
|
|
|
|
Magnetic linear click is a very accurate position sensing Click board™ which utilizes the HMC1501, a magnetic field displacement sensor IC. This integrated sensor uses a single saturated-mode Wheatstone bridge which consists of four magneto-resistive elements. The precision of up to 0.07° in the angular range of ±45° can be easily achieved using the Magnetic linear click, making it far more accurate than the commonly used Hall-effect sensors.
It comes in the package which also includes the mikroSDK™ software and a library with all the functions. The Click board™ comes as a fully tested and approved prototype, making it a reliable device ready to use on the development board.
|
|
|
|
|
|
|
Magnetic rotary click is a very accurate position sensing Click board™ which utilizes the HMC1512, a magnetic field displacement sensor IC. This integrated sensor uses two coplanar saturated-mode Wheatstone bridges which consist of four magneto-resistive elements per bridge. The precision of up to 0.05° in the angular range of ±90° can be easily achieved using the Magnetic rotary click, making it far more accurate than the commonly used Hall-effect sensors.
It comes in the package which also includes the mikroSDK™ software and a library with all the functions. The Click board™ comes as a fully tested and approved prototype, making it a reliable device ready to use on the development board.
|
|
|
|
|
|
|
MCP2517FD click serves as a CAN connector. It carries a DB9 9-pin connector, as well as ATA6563 high-speed CAN transceiver. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller through SPI interface, with additional functionality provided by the following pins on the mikroBUS™ socket: AN, PWM, INT, CS, SCK, MISO, MOSI, TX and RX. |
|
|
|
|
|
|
MCP2518FD click is a complete CAN solution, which can be used as a control node in a CAN network. The Click board™ is used to provide the microcontroller (MCU) with unrestricted access to the CAN network bus. MCP2518FD click is equipped with both the control logic and the physical interface ICs. MCP2518FD click provides a reliable high-speed CAN interface to the MCU, providing multiple operating modes (CAN 2.0, CAN FD, Listen Only mode, Sleep and Low Power mode…), CAN bit stream processing (decoding and encoding of the CAN messages, error handling…), TX prioritizing, RX filtering, FIFO buffer, interrupt engine, and more.
MCP2518FD click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.
|
|
|
|
|
|
|
OLED C click lets you add a small but bright and crisp 1.1" full-color display to your design. It carries a passive matrix OLED display capable of displaying 65K colors, and a SEPS114A display driver and controller. The controller has numerous built-in functionalities like vertical scrolling, horizontal panning, fade in/out, a programmable panel size (partial display), a power saving mode and more. OLED C click communicates with the target board through mikroBUS SPI lines: CS, SCK, and MOSI (SDI); and AN (R/W), PWM (A/C) and RST lines. OLED C click uses a 3.3V power supply. |
|
|
|
|
|
|
WiFi3 is a complete self-contained WiFi solution carrying the ESP8266 module with a system on chip. The module has an integrated TCP/IP stack, supports Wi-Fi Direct (p2p) and boasts powerful processing and storage capabilities that offload all networking functions from the MCU. Alongside a standard mikroBUS socket, with WiFi3 click you’ll also have additional 6 GPIO pins at your disposal. WiFi3 communicates with the target board microcontroller through mikroBUS RX, TX, AN (PWD) and RST (G15) lines. The board uses a 3.3V power supply only. |
|
|
|
|
|
|
BLE2 click is a simple solution for adding Bluetooth 4.1 (also known as Bluetooth Low Energy, BLE, Bluetooth Smart) to your design. It features the RN4020 module from MicroChip that has the complete Bluetooth stack and can act both as a client or a server. Additionally, the RN4020 module supports 13 public profiles and 17 public services, including the MicroChip Low-energy Data Profile (MLDP). BLE 2 communicates with the target board microcontroller through mikroBUS RX, TX and AN (CMD), PWM (CONN), and RST (WAKE) lines. The board is designed to use a 3.3V power supply only. |
|
|
|
|
|
|
BLE 3 click is a quick and simple solution if you want to add Bluetooth Low Energy to your project. It features the NINA-B1 Bluetooth 4.2 module, from u-blox. This click also comes with an integrated antenna mounted on the PCB. |
|
|
|
|
|
|
Flip & click is like an Arduino on one side, but with the added functionality of four mikroBus sockets on the other. This makes it easy for users familiar with Arduino to include functionality from the huge range (160+) of click boards in their designs. The board features an AT91SAM3X8E microcontroller (the same MCU as found on the Arduino Due), the familiar Arduino Uno pinout, and the four mikroBus sockets on the back. In addition to this, four LEDs and a USB host/device connector are also included. |
|
|
|
|
|
<< First
< Previous
Next >
|
|
